Ensurepass.com : Ensure you pass the IT Exams 2018 Jan Juniper Official New Released JN0-343
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/JN0-343.html

Juniper Networks Certified Internet Specialist (JNCIS-ENT)

Question No: 321 – (Topic 4)

Which command statically routes to a next hop that is not directly connected?

  1. set routing-options static route 24.16.42.0/24 qualified-next-hop 64.8.21.3

  2. set routing-options static route 24.16.42.0/24 multihop 64.8.21.3

  3. set routing-options static route 24.16.42.0/24 next-hop 64.8.21.3 recursive

  4. set routing-options static route 24.16.42.0/24 next-hop 64.8.21.3 resolve

Answer: D

Question No: 322 – (Topic 4)

Ensurepass 2018 PDF and VCE

If all OSPF routers shown in the exhibit boot at the same time, which router will be elected as the designated router?

  1. R1

  2. R2

  3. R3

  4. R4

Answer: D

Question No: 323 – (Topic 4)

Your router has the following configuration:

[edit]

user@router# show routing-options router-id 192.168.100.1;

autonomous-system 65505;

Given this information, what is the correct Junos configuration for an IBGP session?

  1. [edit]

    user@router# show protocols bgp group lab {

    type external;

    local-address 192.168.100.1;

    neighbor 192.168.100.2;

    }

  2. [edit]

    user@router# show protocols bgp group lab {

    type 65505;

    local-address 192.168.100.1;

    neighbor 192.168.100.2;

    }

  3. [edit]

    user@router# show protocols bgp group lab {

    peer-as 65503;

    local-address 192.168.100.1;

    neighbor 192.168.100.2;

    }

  4. [edit]

user@router# show protocols bgp group lab {

peer-as 65505;

local-address 192.168.100.1;

neighbor 192.168.100.2;

}

Answer: D

Question No: 324 – (Topic 4)

Two switches are powered on at the same time on the same LAN segment. By default, what determines which switch will become the designated bridge?

  1. the port cost for the associated interface

  2. the bridge ID priority

  3. the total root cost of the switch

  4. the priority of the associated interface

Answer: B

Question No: 325 – (Topic 4)

Which protocol is a link-state routing protocol?

  1. BGP

  2. RIP

  3. OSPF

  4. MPLS

Answer: C

Reference: JNCIS-ENT Routing Study Guide, Open Shortest Path First 鈥?Chapter 3-1

Question No: 326 – (Topic 4)

Which command is used to confirm the status of a tunnel interface?

  1. show tunnel interface gr-0/0/0

  2. show tunnels

  3. show interfaces gr-0/0/0 detail

  4. show interfaces tunnel detail

Answer: C

Question No: 327 – (Topic 4)

The area border router (ABR) between the OSPF backbone area and a not-so-stubby area (NSSA) will suppress which two LSA types for route updates into the NSSA? (Choose two.)

  1. Type 3

  2. Type 4

  3. Type 5

  4. Type 7

Answer: B,C

Question No: 328 – (Topic 4)

You would like the network attached to the ge-0/0/1.0 interface to be advertised into OSPF, but you also want to prevent OSPF adjacencies from being formed on ge-0/0/1.0.

Which command will satisfy this requirement?

  1. [edit protocols]

    user@R1# set ospf area 1 interface ge-0/0/1.0 passive

  2. [edit protocols]

    user@R1# set ospf area 1 interface ge-0/0/1.0 secondary

  3. [edit protocols]

    user@R1# set ospf area 1 interface ge-0/0/1.0 flood-reduction

  4. [edit protocols]

user@R1# set ospf area 1 interface ge-0/0/1.0 disable

Answer: A

Question No: 329 – (Topic 4)

– Exhibit –

Ensurepass 2018 PDF and VCE

– Exhibit –

A packet with a source MAC address of 00:26:88:02:74:23 enters your EX Series switch on port ge-0/0/2.

Assuming the filter in the exhibit has been applied to interface ge-0/0/2, which action will apply?

  1. It discards and counts the packet.

  2. It rejects and counts the packet.

  3. It accepts the packet.

  4. It discards the packet.

Answer: A

Question No: 330 – (Topic 4)

You want to enable nonstop active routing (NSR). Which two commands must you use? (Choose two.)

  1. set routing-options nonstop-routing

  2. set routing-options graceful-restart

  3. set chassis redundancy graceful-switchover

  4. set routing-options graceful-switchover

Answer: A,C

100% Ensurepass Free Download!
Download Free Demo:JN0-343 Demo PDF
100% Ensurepass Free Guaranteed!
JN0-343 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.